Hi everyone,

I’m having a weird issue with text such as the one in this image. Big or small, fancy or regular, all text comes out looking like it does in the image - cracked and hollow. I’ve spent the last few days trying to figure out why, and I’m stumped.

I’ve tried printing slower and slower and adding more and more top layers (the bottom 2 bottle caps are completely solid with 100% infil), but it doesn’t seem to fix the issue.

Here’s what I’m working with:

  • Ender 3
    • Software 2.0.8.27
    • Hardware 4.2.2
  • CR Touch
  • PrusaSlicer 2.8.0
  • MakerBot PLA Filament
  • I’ve used various temperatures and speeds. All of them have generated the terrible text you see here

Thanks in advanced for the help!

Update: We seem to be getting somewhere!

The top 2 are the same ones featured in the post above. The bottom left was printed at 110% extrusion and normal speed. The bottom right was printed at 110% extrusion and a much slower speed for the text, and it looks much better! I’m printing another now with higher bridge flow rate (it was 70%, I set it to 85%), so I’ll update again in a few minutes when that finishes!

Thanks for the information about calibrating e steps from everyone! It’s getting late, so I don’t want to mess around with that tonight, but I’ll give it a shot tomorrow!

Update 2: welp.

That’s possibly the worst one yet. I’m reprinting the bigger insert piece seen in the original post to check if my printer simply can’t do that quality or if it’s the e steps. If it’s e steps, I’m going to bed…

Update 3:

Welp, seems like it’s the e-step. However, it’s too late for me to care about that right now, so I’m going to bed. Thanks for the help everyone! I’ll work on fixing the issue tomorrow

  • IMALlama@lemmy.world
    link
    fedilink
    English
    arrow-up
    7
    ·
    edit-2
    4 months ago

    The upper right print, which is the only one that I can really see clearly, looks under extruded on the top layer. You either have a partial clog, your e-stepe might be ore, or if your printer has always produced top layers that look like that with the filament you’re currently using you need to calibrate (extrusion multiplier and/or temp).

    At a minimum, I suggest double checking e-steps (should take you about 1 minute after your extruder is hot) and your extrusion multiplier.

    I would also check the sliced preview. Ideally all the perimeters of the letters can be the same width. If this isn’t the case, tweak perimeter width until you get there. I’ve found this results in the lowest chances of having a gap in the middle of these types of thin multi-walled features.

    That said, FDM printers have was more resolution in the z axis than they do on x and y. You will be able to get cleaner text, but there’s only so far you can take it.

    • kboy101222@sh.itjust.worksOP
      link
      fedilink
      English
      arrow-up
      4
      ·
      4 months ago

      Thanks for the feedback!

      I’m testing the bottle caps on 110% extrusion right now. Hopefully that’ll solve the issue, cause I have no idea how to go about following that guide on my ender 3. It just says “use the web interface”, which my cheap af ender 3 doesn’t have

      • algorithmae@lemmy.sdf.org
        link
        fedilink
        English
        arrow-up
        1
        ·
        4 months ago

        Ignore all the stuff that says Klipper. Install the program called pronterface and then hook up your printer to your computer with USB. You can then run the commands the guide tells you.

        You should really figure out how to calibrate the esteps if you never have before, it’ll save you a headache. This tutorial is a good visual: https://youtu.be/6PL_rSPZ3M8

        • paf
          link
          fedilink
          English
          arrow-up
          1
          ·
          4 months ago

          Just adding to your comment that if OP goes that route, he will need to cover 5v pin with some electrical tape on usb otherwise he will wreck is printer board. (Unless recent ender 3 have this issue fixed but I doubt)

          • algorithmae@lemmy.sdf.org
            link
            fedilink
            English
            arrow-up
            1
            ·
            4 months ago

            I’ve never heard of that issue before. I have a 2020 year Ender 3 and we have a half dozen at work also around the same age and have run all of them through USB with no problem

            • paf
              link
              fedilink
              English
              arrow-up
              1
              ·
              4 months ago

              If you make a search “ender 3 5v pin”, you will find plenty of examples on Reddit, octoprint forum and others. Problem was (or is) that printer was still getting power when OFF, it could lead to plenty of issues with worst case scenario where the mainboard died.

              • algorithmae@lemmy.sdf.org
                link
                fedilink
                English
                arrow-up
                1
                ·
                4 months ago

                I gotcha. Sounds like as long as you connect USB only when the printer is powered on then you shouldn’t have issues

      • IMALlama@lemmy.world
        link
        fedilink
        English
        arrow-up
        1
        ·
        4 months ago

        To do the e-step process on your ender 3, you would need to open your favorite notepad application, copy/paste the g-code on that site, save the text file as .gcode, and get that g-code to your ender 3 (SD card, etc).

        The same is true for the extrusion multiplier test - you would set the test up in your slicer, slice it, and then print. Some slicers, like orca slicer and super slicer, have a built in extrusion multiplier test that makes it very easy to do this.